● Main use: This machine used for all kinds of powder and granular materials into tablets, is suitable for laboratory and small-scale trial production. It features a small desktop electric continuous tableting machine, or you can hand tablet. The machine can be equipped with a pair dies, filling depth, tablet thickness of the material can be adjusted. ● Features: This model performance, adaptability, easy to use, easy maintenance, small size, light weight, can adapt to all kinds of repression in the pharmaceutical industry, medicine tablet requirements and other industries repression of similar products, deep the industry welcomed by the majority of users. ● TDP-5T single punch tablet machine related parameters are as follows: Model: TDP-5T machine Material: Steel Maximum tablet pressure (kn): 50 kN maximum tablet diameter (mm): 6-18 filling depth (mm): 16 tabletting yield (pc / h): 4000-6000 Motor Power (w): 750 motor speed (r / min): 1400 Weight (kg): 128 Dimensions (mm) (L × C × H): 650 × 440 × 650 ● machine installation: a tableting machine mounted on a solid wooden workbench (can also be installed in the cement platform) with three pay M12 foot screws. Work surface to the ground at a position of about 60 cm body around for the convenience of a disassembly repair, on a wooden bench under a corresponding red core rod should have a hole. Second, the motor power first before turning the motor is properly grounded through to ensure safety. Then remove the V-belt, turn the motor power, motor starting motor rotation direction is correct to observe (the direction of rotation of the motor shaft and the shield should be subject to the direction of the arrow on the wheel or the opposite) If the direction of rotation is incorrect, otherwise the wiring, then put V-belts installed. ● Adjust handling and tableting die die installation: 1, the installation of the red fixing screws screwed Panasonic punch turn the handwheel so that the next red core rod to its highest position, the rod is inserted under the red bar under the red core holes (note the lower punch alignment notch ramp and under the red fastening screws to be inserted in the end) under final punch tighten screws. 2. Loosen the mounted red on the red core fastening nut, put on the red core rod into the hole in the red core rod, to be inserted in the end, with a wrench on the lower part of the six-party red core rod \ on tightening the red fastening nut. 3. Loosen the installation mold mold fixing screws, put the mold into the mold to get flat anti-holes in the plywood, while the lower punch into the hole in the mold, the mold press in the end and then tighten the screws. When placed in the mold should be noted that in the mold of the flat, so as not to get stuck into a crooked, damaged cell walls. 4. Turn the pulley, the upper punch die slowly lowered into the hole to observe whether the collision or friction phenomenon. In the event of a collision or friction, loosen the mold platen fixing screws (two), adjust the position of the fixed mold platen, the upper punch enters the die hole, then tighten the mold platen fixing screws, so adjust means no impact or friction when the party is qualified to install punch into the die until. ● Adjust the piece: turn the hand wheel so that the next punch to its highest position, observation blurted surface is flush with the plane of the mold (or high or low will affect the film) if Sarkozy Loosen the screws butterfly row, Loosen the adjusting gear rotates the gear plate, the lower surface of the mold blurted plane together, and will continue to press on the plate, tighten the screws butterfly row. At this point, with a hand pulley, empty running ten turn, if the machine is working properly, you can feed pressure test, the next step adjustment. ● adjust the fill depth :( That pill weight adjusted) Loosen the butterfly screw line, release the gear plate. By adjusting the gears to make the next left turn red core rod rises, the filling depth reduction (weight loss pills). After adjustment will remain near the gear plate, tighten the screws butterfly row. ● Adjust the pressure :( That tablet hardness adjustment) Loosen the lock nut rod, turn on the red core rod, make a left turn on red core rod moves downward, the pressure is increased, increasing the pressure out of the tablet hardness: Instead, turn to the right, the pressure is reduced, reducing tablet hardness, with a wrench on the lower part of the six-party red core rod after a good tune, will link the lock nut. So far, the adjustment of the die is substantially complete, and then start the motor test pressure 10 SHE sheet, check the tablet weight, hardness and surface finish, such as quality as qualified, to feed production. In the production process, still always check the tablet quality and timely adjustments. ● Die Removal: 1. Loosen the demolition red on the red fastening nut, you can pull out the upper punch, if a tight fit, can hand clamp to live on the red lever to pull it out, but be careful not to damage punch shuttle edge. 2. Loosen the demolition mold mold fixing screws. Chong unscrew the mounting screw, unscrew the screw butterfly line, release the gear plate. Turn the adjustment gear so that the next punch stem rising about 10 millimeters, gently turn the hand wheel, so that the next punch mold core rod will top out in one part of the form is removed by hand, if the mold fit tightly in the hole, not forced to turn the hand wheel hardtop, so as not to damage the parts. Then shall remove the mold platen and then remove the mold. 3, under demolition rushing fixing screws have been unscrewed first, the sub-hand wheel so make undershoot stem rose to the highest position, you can manually pull out the plunger. If you closely, can be hand jaw out (be careful not to damage the punch hook blade). 4, after the demolition die yet turn the adjusting hand wheel, so that the red core rod withdrew about 10 mm, turn the hand wheel to undershoot stem rose to the highest position, which is not higher than the top of the mold platen bottom floor with available (This step is not to be ignored, in order to avoid re-use under the red core rod and the mold contradict the accident). Finally will undershoot the fixing screws screwed on. ● lubrication and maintenance: 1, all moving parts lubricated friction surfaces is to ensure the normal operation of the machine and prolong the life of an important part, especially if the main moving parts move rapidly under starvation conditions dry damaged and can not be used, so tableting machine before using all the oil cup, plus hole and surface friction lubricants and empty running so that all the friction face full of film, and then be put into use. Press to refuel next class, but each refueling can not be too much to avoid spillovers clean, stain pills. 2, before the class must check all the screws are loose, in the course of their work should always pay attention to check, if loose, tighten immediately, in order to avoid failure. 3, before and after each use classes are required to hand-tune the pressure test every few pieces, no problem and then open the electric tablet. 4, in the tabletting process should always check the quality of the die, if there is lack of edge, cracks, becomes a serious loss, should be replaced, in order to avoid damage to the machine malfunction and affect the quality of the tablet. 5. After each use the remaining particles removed, wipe clean the machine ministries. If downtime is longer, shall remove the die, the machine each friction surface, wipe Face coated with anti-rust oil, dust cover clothing; immersed in oil saved die should wipe. I plant specializing in the production of single punch tablet machine medicine, multi-punch rotary tablet machine, powder pellet mill, three-dimensional mixer, groove mixer, V-type mixer, stainless steel mill, traditional Chinese medicine pill machine, food herbs dryer, tablet pill coating machine, feeding machine and other small laboratory equipment.